Put down newspaper or butcher paper on tables and countertops to catch spills and for easy cleanup.
Have paper towels and Windex on hand for cleaning stovetops.
Wrap stove burner bowls in tin foil to catch drips of wax, and for easy cleanup afterwards.

Spray inside of the votive mold with silicone mold release spray, if you are using it. To do this follow the directions on the Silicone Mold Release Spray, or hold the spray nozzle 8 to 10 inches from the votive mold and spray the inside with one or two short bursts.
Place votive mold open end up on the work surface, make sure it is a FLAT LEVEL SURFACE

Place tabbed votive wick inside the votive mold. Try to get them at center, although during pour they will probably shift to one side a little.

You will need either a steamer pot or deep sauce pan, and you will also need a melting pot with a pouring spout. These two items create a double boiler to melt down your wax.

Fill the bottom part of your double boiler (the steamer pot or the deep sauce pan) with about two inches of cool water, and place on the burner set to high temperature. Place pieces of wax to be melted into the melting pot with a pouring spout, set the melting pot in the water, and attend to it as the wax liquefies. (When the water begins to boil, turn the heat down to medium low or low.)

NOTE: Never leave wax unattended on stove.

When the wax is entirely liquid (i.e., when there are no solid chunks any longer in the pot) you have successfully melted the wax.

To check temperature of wax, immerse thermometer in wax, taking care not to let it touch the bottom of the melting pot. 130 degree votive candle wax melts at about 130 degrees F. The wax will continue to grow hotter as it remains in the double boiler. The temperature of the wax should get to 190 degrees F.

After the wax is entirely melted and at about 190 degrees F, add your candle dye, if you are using any. Each of our diamond shaped dye chips colors 1 lb of wax. Use more or less for lighter or darker colored candles. Drop a dye chip (or part of a dye chip) into the melted wax, and stir until the wax chip is entirely dissolved.

Adding Fragrance

Adding fragrance is the last thing you do before you pour the candle. This is because the potency of the fragrance can be reduced if subjected to high heat for too long.

After the wax is entirely melted, and after you have added candle dye (if you are using candle dye), add your candle fragrance, if you are using any. The standard ratio for our candle fragrance oils is one ounce of fragrance oil per 1 lb of wax. Use more or less for lighter or heavier scented candles. Add the candle fragrance to the melted (and colored, if you are making colored candles) wax in the melting pot, and stir thoroughly to get even distribution of the candle fragrance.

NOTE: Excessive fragrance oil usage can damage plastic molds. If you are using a plastic mold for this project, please do not overdo the fragrance oil.

The ideal pouring temperature for votives is 175 degrees F, so you will need to remove the double boiler from the heat source to allow the wax to cool to 175 degrees F (170 to 180 degrees F is an acceptable temperature range for pouring votive candles). However, we are making simple, stress free votives here, so don’t spend too much time worrying about the temperature of the candle wax before you pour it. (My favored method for votives is to wait to pour until I can just begin to see the wax solidifying (congealing) on the inside surface of the melting pot.)

To check temperature of wax, immerse candle thermometer in wax, taking care not to let it touch the bottom of the melting pot.

Pour: You need a spouted container to pour votives. You can also use a wood stirring stick or a chopstick for added pouring control to reduce dribbles.

Fill the votive mold up to the rim with wax. Be sure to save about 20% of your melted wax for the second pour you will make after the candles set.

Set: After making the first pour of wax into the votive molds, let the votives stand undisturbed while the wax shrinks and they cool completely. It generally takes a votive about an hour to an hour and a half (my experience is usually no longer than 2 hours, although some people report cool times of up to 4 hours) for the wax in the mold to cool and shrink. As the votive cools in the mold, the wax shrinks creating a depression in the center around the wick.

5. 2nd Pour of Votive Candle Wax

The “second pour” is made after the wax in the votive candle mold has cooled completely. The reason for making a second pour (pouring more wax into the mold after the first pour wax has cooled) is that the wax from the first pour will have shrunk into a sink-hole around the wick. This is normal, as wax expands when melted and contracts when it cools.

To make the second pour for a votive candle, re-heat the remaining wax and pour it into the depression of the cooled wax in the votive candle mold.

NOTE: Some people like the re-pour wax temperature to be about 10 to 15 degrees hotter than the temperature of the initial pour wax. This is a matter of style and although it is reported by some that this method aids adhesion of the 2nd pour wax to the first pour wax, it is completely optional. Beginning votive candle makers need not worry over this, as all the votives will end up in a votive candle holder and, as votive candles do, liquefying as they burn.

When making the second pour, fill the votive mold up to the rim, and just a bit higher, taking care not to fill it so much that wax dribbles over the edge.

The correct level of wax for the 2nd pour of a votive creates the slight lip at the top of a votive.

· If you have used silicone mold release spray, and the candle is completely cool, you should only have to turn the votive mold upside down and shake it a little to get the candle to fall right out into your hand

· If you didn’t use silicone mold release spray, try just turning it over and shaking it. If it doesn’t come out into your hand easily, try twisting the candle in the mold to loosen it.

· If that does not work, then drop the candle-filled votive mold into a large glass of warm water and leave it alone. It will eventually be set free by the water and float to the surface.

· Votive candles need to be burned in votive holders

· Before you burn your new votives, put a little bit of water and a couple drops of liquid dish soap in the bottom of the holder. When the votive is finished burning, the wax shell will pop out easily, so you can recycle it again!